EXACTLY HOW TO INSTALL A BATH TUB: INSTALL AN ACRYLIC TUB AND ALSO TUB SURROUND

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround

Blog Article

Visit My Website

In this article down the page you can find some excellent news around How to Install a Bathtub.


A Step-by-Step Guide to Installing a Bathtub
Mounting a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as are comfortable trying it. Rather than working with a professional to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will help you set up a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous supply of water pipes.
Your devices as well as material list ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installation


    To start with, the supporting structure supplied with the bathroom should be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
    Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.

    Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted gain access to that is often the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
    Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Making use of both wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub up until the spirit level reads level.
    To mount faucets, fit all-time low of the outermost flexible tap connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the other tap.
    Turn on the supply of water and also inspect all joints and brand-new pipework for leakages and also tighten them if required. Fill the bath tub and also check the overflow electrical outlet and the typical outlet for leaks.
    Lastly, fix the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the bathtub ought to wait up until the bath tub has actually been made use of at least when as this will certainly resolve it right into its final placement.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the mounting opening in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, triggering the water to pass through the wall between the bath as well as the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
    You can pick from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this motion prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    As an avid person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that topic was important. Be sure to set aside a second to promote this page if you enjoyed it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.




    Services


    Report this page